Skip to Content
Kenall Manufacturing - Homepage
Main Content

MLHA12-ICT

Millenium Stretch

MLHA12-ICT Main Image
MLHA12-ICT Main Image
Model #: MLHA12-ICT
Features:
  • Provides environmental disinfection and effective, efficient lighting performance via visible LED light
  • Dual-Mode Indigo-Clean Technology is independently tested to kill 94% of SARS CoV-2 and Influenza-A***, in addition to MRSA
  • Single-Mode Indigo-Clean Technology is independently tested to kill harmful bacteria, such as Staph*, including MRSA**
  • Peace of Mind Guarantee™ against breakage
Application(s):Parking Garage
Parks and Recreation
Packaging and Staging
Kitchen and Food Prep
Locker Rooms
Multifamily Housing
Cafeterias
Walkways
Washrooms (Correctional)
Restrooms
Stairwells
Showers
Dorm Rooms
Schools and Universities
Transportation Platforms
Foyers and Lobbies
Corridors
Sally Ports
Exteriors and Entryways
Gymnasiums and Multipurpose Rooms
Natatoriums
Manufacturing
Lens Type(s):Frost High Impact Acrylic
Lamp Type(s):LED
Size(s):12"W
Listings:      
Specifications are subject to change without notice. Please consult your Kenall Customer Service for help with special requests at (800) 4 Kenall.

Technical Specifications

Electrical
(Single- and Dual-Mode ICT) Serviceable mid-power white and 405nm Indigo LED array. Available 3200K, 3700K and 4300K color temperatures with 3-step MacAdam variation allowance. Minimum 82 CRI standard. 120-277VAC and 347VAC electrical input with serviceable high power factor electronic, constant-current drivers (<10% THD, >0.90 PF). Minimum 85% driver efficiency. Standard 0-10V dimming with 1-100% range and dim-to-dark capabilities. 330μA maximum source current. Single-Mode ICT provides a single, white disinfection operational mode. Dual-Mode ICT provides two operational modes based on room occupancy.  White Disinfection Mode is a white LED array for ambient lighting plus a simultaneous low-power 405nm LED array for low-level, continuous and safe environmental disinfection.  Indigo Disinfection Mode is a higher-level 405nm array for continuous safe environmental disinfection during periods of room vacancy.  The operational mode is determined via internal low-voltage device based upon the input signal provided by an external control device/system.  Luminaire dimming is overridden in this operational state.  Refer to the Kenall Dual-Mode ICT Control Application Guide for further description. 
 
End CapsMarine grade die-cast aluminum. Three styles available: Flat, Rounded and Reveal. Conduit and ”Wiremold™ ready” knockouts visible only from interior of end cap (Flat and Rounded styles only).
HousingMarine grade aluminum. Extruded body with die-cast end caps. Housing, with end caps, post assembly TGIC polyester powder coat finished – 5-step pre-treatment. See Ordering Information for available finishes.
InstallationStandard six-point mounting required for Peace of Mind Guarantee®. Suitable for installation into -30°C to 40°C ambient environments, unless otherwise noted.
ListingsLuminaire is certified to UL Standards by Intertek Testing Laboratory for Wet Location – covered ceiling mount. ETL certified IP64 per IEC 60598. Damp rated – ceiling mount. Corner, horizontal wall and pendant mount installation – damp location only. ADA compliant.
OpticsHigh-impact extruded diffuser. Smooth exterior, linear prismatic interior. Nominal thickness .156". Lens securely positioned in body channels and end caps. Lens locked in place with four (4) tamper-resistant stainless steel Torx® with center pin fasteners and sealed with closed cell gaskets. Full reflector/wire cover with 92% reflectivity.
PhotometricsPhotometry tested to the IESNA LM-79-08 standard by an ILAC/ISO17025 accredited laboratory. For additional photometric data, please go to www.kenall.com.
WarrantyLimited five (5) year warranty for LED Lamps. Peace of Mind Guarantee™ when installed as noted above.

This product complies with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin.

Downloads

Product Documentation

Installation Files

Photometry (IES)

Additional Resources

top